كورس تصميم المنشآت المعدنية (المستوى الثالث)
د.إيليا حنين
يستكمل المستوى الثالث من دبلومة تصميم المنشآت المعدنية تصميم المنشآت المعدنية بإستخدام المعادلات والمبادئ الأساسية بإستخدام الكود الأمريكي AISC 360-16 , ويستكمل المستوى الثالث العديد من الموضوعات الهامة مثل : Anchoring to concrete بنوعيها Cast-in place anchors او post install anchors بالأضافة لشرح برنامج PROFIS Engineering Suite وذلك كما هو موضح بمحتوى الدورة.
نبذة عن دورة تصميم المنشآت المعدنية (المستوى الثالث)
يستكمل المستوى الثالث من دبلومة تصميم المنشآت المعدنية تصميم المنشآت المعدنية بإستخدام المعادلات والمبادئ الأساسية بإستخدام الكود الأمريكي AISC 360-16 , ويستكمل المستوى الثالث العديد من الموضوعات الهامة مثل : Anchoring to concrete بنوعيها Cast-in place anchors او post install anchors بالأضافة لشرح برنامج PROFIS Engineering Suite وذلك كما هو موضح بمحتوى الدورة.
دبلومة تصميم المنشآت المعدنية تتكون من 6 مستويات مختلفة , يتخص اول 4 مستويات منهم بدراسة الأساسيات و 2 مستوى يختصان بدراسة موضوعات متقدمة.
✅بتقدر تستفيد من اى أضافات مستقبلية للدورة بشكل مجانى .
✅ ️جودة تسجيل احترافية صوت وصورة عالية الوضوح .
✅يمكنك الاشتراك بالدورة من أي مكان فى خطوات معدودة.
✅طرق مدفوعات متنوعة.
الفئة المُستهدفة من الدورة:
- الكورس يناسب الطلبة وحديثي التخرج المهتمين بتعلم مجال تصميم المنشآت المعدنية.
أساسيات لازمة قبل البدء فى الدورة:
- يشترط الإنتهاء من المستوى الاول والثاني لدبلومة تصميم المنشآت المعدنية
- الجدية في التعلم والمذاكرة.
- تخصيص عدد 4 مذاكرة أسبوعيا.
ما الذي ستكتسبه بنهاية الدورة:
- فهم سلوك وتصميم العناصر المعدنية.
- فهم التحليل الإنشائي للمباني المعدنية.
البرامج المستخدمة فى الدورة:
- الكورس لا يحتوي على برامج وذلك لأنه يشرح الحل بشكل يدوي.
محتوى الدورة:
Anchoring to concrete
- Cast in place anchors
- welded studs.
- Head Anchors.
- J-bolts.
- Post Install anchors
- Mechanical anchors (undercut, Wedges).
- Screw anchors.
- Adhesive anchors.
- Reinforcement anchoring in existing concrete.
- PROFIS Engineering Suite Software from HILTI
- Introduction and codes governing the design.
- The behavior of anchors and failure mechanisms.
- Load distribution.
- Design Required Strength.
- Loads on anchors under compression forces.
- Loads on anchors under tension.
- Steel Strength requirements.
- Concrete breakout Strength requirements.
- Pullout Strength requirements.
- Side Face blowout Strength requirements.
- Bond strength requirements -adhesive anchors force Loads on anchors under shear.
- Steel Strength requirements.
- Concrete breakout strength requirements.
- Pry out Strength requirements.
- Shear lug design.
- Combined tension and shear interaction.
- Requirement Edge Distance, spacing, and thickness to prevent splitting failure.
- Earthquake-resistant anchor design requirements.
- Base plate.
- Column base plate design.
- Beam bearing plate design.
- Anchor Rod material.
- Anchor rod holes and washers.
- Anchor rod sizing and layout.
- Base plate under concentric compression with and without confinement.
- Small moment base plate design.
- Large moment base plate design.
- Single-headed anchor under tension and shear.
- Single End Hook Anchor – Tension and Shear.
- Single Post Install expansion – Tension and Shear.
- Single Post Install Adhesive – Tension and Shear.
- Single Screw Anchor – Tension and Shear.
- Cast in place Studs (group) – Tension.
- Post Installed Adhesive Anchors (group) -Tension.
- Cast in place Studs (group) Subjected to Shear Force and Moment.
- Post-installed adhesive group of anchors (group) Subjected to Shear force and Moment.
- Cast in place Studs (group) SubJected to tension force applied eccentrically
to the two axes symmetry. - Post-installed adhesive group of anchors resisting tension force applied eccentrically to the two axes of symmetry.
- Cast in column baseplate anchors resisting tension and shear forces.
- Post Installed adhesive column anchors resisting tension and shear.
مقتطفات من أسلوب الشرح
عن المحاضر:
Eliya Henin, Ph.D., P.E., S.E, PMP
Associate professor (on leave) at Assiut University – Egypt
- Registered as Professional Civil Engineer (PE) in multiple States – USA
- Professional Structural Engineer (SE) in multiple States – USA
- Certified Bridge Inspection Team Leader
- Certified Project Management Professional (PMP).
- Experience in precast/prestressed concrete products (bridge, building, and industrial products), such as girders, floor systems, manholes, electrical vaults, feed mills, flour mills, grain storage facilities, truck and rail receiving and ancillary buildings.
- Design of several steel and concrete structures with seismic considerations.
- Strong background and knowledge in construction planning, coordination, and management.
- Experience in different project delivery systems including design-built and design-bid-built.
- Expertise in identifying, analyzing, and solving problems through communications and visualization.
- Progressive research activities and publications (17 articles in scholar journals and referred conferences).
- Outstanding teaching at both undergraduate and graduate levels
منتجات ذات صلة